Nikko Steel Kawat Las Elektroda Mo & CrMo Alloyed Heat & Creep Resisting Steels RD-16B9

Brosur & Katalog Produk / Brosur & Katalog Produk

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

Post comment with email address (confirmation of email is required in order to publish comment on website) or please login to post comment

1. MANUFACTURERS OF A DIVERSE RANGE OF ADVANCED WELDING CONSUMABLES SECTION 5 RD-16B9 BASIC LOW HYDROGEN ELECTRODE FOR WELDING MODIFIED 9Cr-1Mo STEELS OPERATING AT ELEVATED TEMPERATURES UP TO 650 º C DATA SHEET NO. 55 SPECIFICATION AWS A5.5 BS EN 1599 CLASSIFICATION E9016-B9 E CrMo91 B PRODUCT DESCRIPTION The design emphasis of the chemically basic flux is engineered to ensure the optimum weld metal properties demanded by the specification are fully met. The basic flux containing the appropriate alloying elements but minimal iron powder, is extruded onto a high purity ferritic core wire and bound with a blend of silicates that ensure both coating strength and a coating resistant to subsequent moisture absorption . WELDING FEATURES OF THE ELECTRODE The chemical nature of the flux together with its controlled coating factor allows the electrode to be used at relatively low amps. This factor together with the fairly fluid but quick freezing slag facilitate vertical up welding including controlled penetration root runs. Overall the arc is very stable, slag detachability is good, fillet welds are slightly convex and metal recovery is some 98% with respect to weight of the core wire. APPLICATIONS AND MATERIALS TO BE WELDED PLATE ASTM A387 Grade 91, TUBES/PIPES ASTM A335 Grade 91, A234 Grade WP91, A199 Grade T91, A213 Grade T91. BS 3604 Grades CFS & HFS 629-470 CFS/HFS 629-590. FORGINGS A182 Grade F91, A336 Grade F91 CAST ASTM A217 Grade C12A, BS1503 Grade 91 PWHT recommended range is 745 - 775 º C (2 hours), pre-heat 200 - 300 º C. Cool to 150 º C before PWHT. WELD METAL ANALYSIS COMPOSITION % BY Wt. C Mn Si S * P* Cr Ni Mo Nb V Al N MIN 0.08 - - - - 8.0 - 0.85 0.02 0.15 - 0.02 MAX 0.13 1.2 0.30 0.015 0.015 10.5 0.8 1.2 0.10 0.30 0.04 0.07 TYPICAL 0.10 0.9 0.28 0.01 0.01 9.0 0.4 1.0 0.03 0.22 0.01 0.03 * AWS A5.5 specifies S = 0.01% max. and P = 0.01% max. ALL WELD METAL PROPERTIES (AFTER PWHT) PROPERTY UNITS MINIMUM TYPICAL OTHERS Tensile strength N/mm 2 620 750 – 880 0.2% Proof stress N/mm 2 530 620 – 780 Elongation on 4d % 17 21 Reduction of Area (RA) % - 60 Impact energy 20 o C J - 65 Results relate to PWHT 765ºC furnace cooled WELDING AMPERAGE AC or DC+ Ø (mm) 2.6 3.2 4.0 5.0 MIN 50 75 130 180 MAX 85 125 170 220 OTHER DATA Electrodes that have become damp should be re-dried at 150 o C for 1 hour. RELATED PRODUCTS Please contact our Technical Department for detail. WI-0304 DS55 RD-16B9 Rev. 5, Date 01.01.201 3

Dilihat

  • 80 Total Views
  • 49 Website Views
  • 31 Embeded Views

Tindakan

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 2

  • 3 sentral.indoteknik.com
  • 6 indoteknikcom.odoo.com